TrainAidsA - T-Gauge the Worlds Smallest Model Train System


On Jan. 22, 2012
US Postal System rates have increased
dramatically for both domestic and international mailings.

LED's

SMD | Strips | Connectors | LEDs for Lionel |
Bayonet, Cartridge & Screw Base LEDs

No PayPal ? No problem !

We accept Checks or Money Orders.
Don't use the Cart? Then email requirements and address for total
& just pay via PayPal.
We ship only when payment clears.
About our LEDs
Our LEDs A Light Emitting Diode (LED) is today's preferred illumination technology. LEDs consume less power, do not heat up and produce a stronger light while lasting much longer.

Most of our products are Plug-n-Play with the resistor integrated into the assembly. The individual C5 and SMD LEDs need voltage & current control. C5 packages include resistors for use with 9-19v DC.

For conversion from incandescent lamps/bulbs, we have introduced a variety of LEDs. E5 & C5 are designed to replace older bulbs. The Strips, which are also Plug-n-Play, use SMD type LEDs, C5, E5, W5, W3's are glass dome type. Dome types produce a narrow directional forward illumination. SMD's produce a wider angle of illumination.
For AC & DCC
For AC & DCC: To use our strips with AC power as in Märklin, or in situations where you would like them to light up in forward and backward movement (positive/negative polarity change), the best way is to feed power via a rectifier to neutralize the flickering or polarity change.

We suggest ACW (see below) a wire connector for strips, which has a built-in mini rectifier. OR ACCW (see below) a wire connector for strips (or other LEDs), which has a built-in mini rectifier AND a capacitor to avoid flickering when the train passes over a gap or power is interrupted for some reason.
 
You may add a mini rectifier that can also be ordered via our Elektrizmos section.
Polarity
LED Polarity is Important LEDs are polarity sensitive, except those for Lionel which include a rectifier to allow them to work in forward and reverse travel and also with AC such as in Märklin.

Wires presoldered with our LEDs, connectors etc., such as W3 or W5, follow this standard rule:
Black wire is Negative (-) and  Colored wire is Positive (+).
 
Lionel Users: Please see items  E5, E10, L2S, L1T & L3. Most of these LEDs have Rectfiers built into them for working with either polarity.
 
See also: For AC & DCC next on left.
Power Pickup
Power Pickups:
 An exact fit may not be available for many specific axle/wheel wiper installations, so TrainAidsA has created
 
"Universal/Combination Axle/Wheel Wiper".
 
 
Click Here for Installation Instructions.

Technical: Our LED Support section provides additional information on most of the items here. For Resistors, Rectifiers etc. please visit the Elektrizmos section.

Status: Item in stock In Stock | Currently not in Stock Not in Stock | Shipping Soon or Date Shipping Soon or Date will display
Mouse over icons for details. See also Shipping+Availability.

On the right: Comparison of Warm-White & White LED illumination.

White/Warm White ?
A White LED is more bluish in color and looks like the flourescent tube light or the headlamps in new cars. The light temperature is 5,000° K.

The Warm-White or also called Golden White emits light that is more like the traditional incandescent bulb and emits light at 3,000° K.
SMD Floodlight
(by Viessmann - Germany)
 

HO Scale Floodlight (Viessmann 6333 - Made in Germany)

Tilts up or down, realistic use possible. Wide angle SMD light. Stays cool. Use directly in Towers, on buildings and for other Accessories & locations. 5mm dia. overall with wired-in resistor. Comes with instructions on use with AC/DC systems.

Recommended use with 14-16v AC/DC.

View PDF Manual
(Details: Click image) 		Ready to use LED based Flood Light.
Sold singly.
Prewired with resistor to use with 14-16v AC/DC.
 
Stock Status Price: $9.99 Each.
Viessmann Logo

C5 - Cartridge Base

Normal Polarity: Center Bottom Terminal Positive & Casing Negative. For opposite polarity, see next item CR5 below.
Note: Both C5 and CR5 should be used where the bulb cannot be replaced with LEDs in other shapes and solutions. LEDs are polarity sensitive, so in many cases, the wiring in older locomotives or cars is not suitable for a simple direct replacement.
Length (Bottom Tip to Top): 13mm.
C5: Our Cartridge Base LED (Designed and produced by TrainAidsA)

Use as replacement in Locomotives, Turnouts, Vehicles, Trackside Accessories & other locations. 5mm dia. LEDs, without built in resistor. Similar mount as Marklin 600100 (5mm dia. base). Resistors supplied with LEDs and included in price.

Normal use with 3-3.5v DC, and with upto 19v with resistor supplied.

Offers flexibility in installation with both polarities available as needed. See CR types for opposite/reversed polarity

Please check out our LED Support section, that provides additional information.
(Details: Click image) 		C5 LEDs are Available in Packets of 2 Each in Following Clear Colors:
Stock Status C5WH: White
Price: $1.50 per pkt.
Stock Status C5AM: Amber
Price: $1.50 per pkt.
Stock Status C5WW: Warm White
Price: $1.50 per pkt.
Stock Status C5RD: Red
Price: $1.50 per pkt.
Stock Status C5YE: Yellow
Price: $1.50 per pkt.
Stock Status C5GR: Green
Price: $1.50 per pkt.

CR5 - Cartridge Base (Rev. Polarity)

(Designed and produced by TrainAidsA)

Same as C5, but with Reverse Polarity: Center Bottom Terminal is Negative & Casing Positive. Use as replacement in Locomotives, or where reverse polarity version of C5 is required. Comes without built in resistor similar to C5. Resistors supplied with LEDs and included in price.

Märklin users: This is similar to Märklin 600100. Item C5 above is normal polarity.

CR5 LEDs are Available in Packets of 2 Each in Following Clear Colors:

Stock Status CR5WH: White
Price: $1.50 per pkt.
Stock Status CR5WW: Warm White
Price: $1.50 per pkt.

E5 - Screw Base
Length (Bottom Tip to Top): 14mm.
E5
Our Screw Base LED
(Designed and produced by TrainAidsA)

Assembled with resistor in the body. Plug-n-Play - Use as replacement in Turnouts, Vehicles, Trackside Accessories & other locations. 5mm dia.
 
LEDs, with built in resistor. Fits E5.5 (5.5mm dia.) sockets or other similar mounts.
 
Fits Lionel 6-24103 Light Towers
 
Designed for use for 12v-19v, but will work with lower voltages upto 9v.
 
Our LED Support section provides additional information.
(Details: Click image)
E5 LEDs are Available in Packets of 2 Each in Following Clear Colors:
Stock Status E5WH: White
Price: $1.50 per pkt.
Stock Status E5AM: Amber
$1.50 per pkt.
Stock Status E5WW: Warm White
$1.50 per pkt.
Stock Status E5RD: Red
$1.50 per pkt.
Stock Status E5YE: Yellow
$1.50 per pkt.
Stock Status E5GR: Green
Price: $1.50 per pkt.
Lionel Logo These E5 LEDs also fit Lionel 6-24103 Light Towers.

Physical Comparison of L1T, E5 and E10 LED Sizes:

For more details, see: Large LEDs Support

Sizes:

Physical Comparison of L1T, E5 and E10 LED Sizes:
E5 (center) have a base of 5.5mm diameter and E10 (right) have a base of 10mm diameter.

L1T, L2S, L3 & E10 type LEDs have resistors and Rectifiers built into the base for use with AC, DC & DCC if necessary.
 
The E5 Fits Lionel 6-24103 Light Towers
Note:
These are not sold as a pack of three. This picture just demonstrates the difference in sizes and shapes of the three types.

Select for use: With Dome or without.
Click Pictures for a larger view and details.

Install with Dome or without:

Install with Dome or without.
(Designed and produced by TrainAidsA)

Our LEDs for Lionel are ready for use without any additional work.

E10 - Dome LEDs

E10: Our large Dome LEDs
(Designed and produced by TrainAidsA)

Our LEDs for Lionel are ready for use without any additional work.

For more details, see:
E10 LEDs Support

Dimensions:
Bottom Tip to Top:
      28mm ( 1-1/8 inch)
Base Diameter:
      9mm ( 5/16 inch )
Base Type:
      E10
(Details: Click image) 		Use much less power and stay cool to touch !
No more melted switch covers. You don't need the covers. The dome shape has the same look as the covers. Remove the old covers and bulbs and Just Screw these in !!!!!

Resistor built inside.
Rectifier inside for compatibility to work with opposite polarity or AC.

E10 Dome LEDs are Available in Packets of 2 Each in Following Colors:

Stock Status E10-WH: White (Milky/Frosted)
Price: $2.50 per pkt.
Stock Status E10-RD: Red (Clear)
Price: $2.50 per pkt.
Stock Status E10-GR: Green (Clear)
Price: $2.50 per pkt.
L_Logo-lg
Ideal Replacement for Incandescent Bulbs/Lamps in
Older Lionel Switches and Controllers (e.g. 0-22 & 5133)
Fit Bulb Sockets: 52, 258, 428, 432, 1446, 1447 & 1449
and other locations where the same base can fit.

L2S - Flat Top LEDs
L2S: Our Flat Top LEDs
(Designed and produced by TrainAidsA)


Dimensions:
Bottom Tip to Top:
      25mm ( 15/16 inch)
Base Diameter:
      9mm ( 5/16 inch ) Base Type:
      E10


Our Large LEDs Support section provides additional information.
(Details: Click image) 		No more melted switch covers. Just Plug in !!!!!

Use much less power and stay cool to touch !

Resistor built inside.
Rectifier inside for compatibility to work with reverse polarity or AC.

L2S Flat Top LEDs are Available in Packets of 2 Each in Following Colors:

Stock Status L2S-WH: White (Clear)
(Need Milky?)
Easy Milky LEDs:
 Take a fine sandpaper and roughen the front face of the LED. Unless you specifcally need to frost the sides, there is no need as LEDs generally "project" illumination in "front" only.
 
Price: $2.50 per pkt.
Stock Status L2S-RD: Red (Clear)
Price: $2.50 per pkt.
Stock Status L2S-GR: Green (Clear)
Price: $2.50 per pkt.

L_Logo-lg
Ideal Replacement for Bulbs/Lamps in
Lionel Switches & Controllers (e.g. 0-22 & 5133) with
Screw Mounts for use with Dome shaped Covers
or Loco/Passenger car lights.
Fit Bulb Sockets: 52, 258, 428, 432, 1446, 1447 & 1449

L1T - Flat Top LEDs
L1T: Our Flat Top LED
(Designed and produced by TrainAidsA)


Our L1T LEDs Support section provides additional information.

Dimensions:
Bottom Tip to Top:
    25mm ( 15/16 inch)
Base Diameter:
    9mm ( 5/16 inch )
Base Type:
    BA9S
(Details: Click image) 		Cool to Touch !!

Just Plug in !

Resistor built inside.
Rectifier inside for compatibility to work with opposite polarity or AC.

L1T Flat Top LEDs are Available in Packets of 2 Each in Following Colors:

Stock Status L1T-WH: White (Milky/Frosted)
Price: $2.50 per pkt.
Stock Status L1T-RD: Red (Clear)
Price: $2.50 per pkt.
Stock Status L1T-GR: Green (Clear)
Price: $2.50 per pkt.
L_Logo-lg
Ideal Replacement for Bulbs/Lamps in
Lionel Switches & Controllers (e.g. 0-22 & 5133) with
Bayonet Mounts for use with Dome shaped Covers.
Fit Bulb Sockets: 53, 57, 182, 257, 363, 1445 & 6253

L3 - Round Dome Top LEDs
Lionel LED L3
L3: Our Round Dome Top LED
(Designed and produced by TrainAidsA)


Note: The length is longer than traditional bulbs due to the shape & size of the LED.
 
Our L3 LEDs Support section provides additional information.

Dimensions:
Bottom Tip to Top:
    28mm ( 1-1/8 inch )
Base Diameter:
    9mm ( 5/16 inch )
Base Type:
    BA9S
(Details: Click image) 		Use much less power and stay cool to touch !
No more melted switch covers. You don't need the covers. The dome shape has the same look as the covers. Remove the old covers and bulbs
. . . . and Just Plug in !!!!!

Resistor built inside.
Rectifier inside for compatibility to work with opposite polarity or AC.
L3 Dome LEDs are Available in Packets of 2 Each in Following Colors:
Stock Status L3-WH: White
(Milky/Frosted)
Price: $2.50 per pkt.
Stock Status L3-RD: Red (Clear)
Price: $2.50 per pkt.
Stock Status L3-GR: Green (Clear)
Price: $2.50 per pkt.
L_Logo-lg
Ideal Replacement for Bulbs/Lamps in
Lionel Switches & Controllers (e.g. 0-22 & 5133) with
Bayonet Mounts for use with Dome Covers/Lenses.
Fit Bulb Sockets: 53, 57, 182, 257, 363, 1445 & 6253

W3: 3mm Round Dome Top LEDs
W3: Our 3mm Round Dome Top LED
(Designed and produced by TrainAidsA)

 
Power:
      12v DC to 19v DC
Max. Forward Current:
      60mA (Reduce if possible for voltage above 12v)
Max. Normal Current:
      40mA
Max. Reverse Voltage:
      10v.

Our LEDs Support section provides additional information.
(Details: Click image)
LED Wired with Resistor. Plug-n-Play - ready to use in buildings, in lamp posts, as signal lamps, in turnouts, inside vehicles, trackside, tunnels & other creative locations. 3 mm dia.

W3 LEDs are Available in Packets of 2 Each in Following Clear Colors:
Stock Status W3WH: White
Price: $1.50 per pkt.
Stock Status W3AM: Amber
Price: $1.50 per pkt.
Stock Status W3WW: Warm White
Price: $1.50 per pkt.
Stock Status W3RD: Red
Price: $1.50 per pkt.
Stock Status W3YE: Yellow
Price: $1.50 per pkt.
Stock Status W3GR: Green
Price: $1.50 per pkt.


W3 LEDs are also Available in Packets of 2 Each in Following Milky Color(s):

Stock Status W3WH-M: Milky White
Price: $2.00 per pkt.
Stock Status W3WW-M: Milky Warm White
Price: $2.00 per pkt.


W5: 5mm Round Dome Top LED
W5: Our 5mm Round Dome Top LED
(Designed and produced by TrainAidsA)

LED Wired with Resistor. Plug-n-Play - ready to use in buildings, vehicles, trackside & other creative locations. 5mm dia. Each with built in resistor & 20 cm wire leads ready to connect to 12v-19v DC.

Power: 12v-19v DC
Max. Forward Current: 60mA (Reduce if possible for voltage above 12v)
Max, Normal Current: 40mA
Max. Reverse Voltage: 10v.

Our LED Support section provides additional information.
(Details: Click image) 		W5 LEDs are Available in Packets of 2 Each in Following Clear Colors:
Stock Status W5WH: White
Price: $1.50 per pkt.
Stock Status W5AM: Amber
Price: $1.50 per pkt.
Stock Status W5WW: Warm White
Price: $1.50 per pkt.
Stock Status W5RD: Red
Price: $1.50 per pkt.
Stock Status W5YE: Yellow
Price: $1.50 per pkt.
Stock Status W5GR: Green
Price: $1.50 per pkt.

SMD LEDs - Prewired 3528            Save on soldering time and trouble!
SMD-3528:
Our 3528 SMD LED
(Designed and produced by TrainAidsA)

Supplied with 4 Resistors (2/LED) and two Diodes for current control. Yellow LEDs come with 8 resistors (4/LED)and 2 Diodes.
 
SMD Type: 3528
 
Please check out our
LED Support section for dimensions & voltage information.
(Details: Click image) 		SMD (Surface Mount) LEDs individually prepared for your convenience with 18in. (50cm) long wire leads pre-soldered to each.

As they have a wider angle of illumination, they are great for installation in a variety of locations in your layout, cars, stations, inside buildings, behind windows or in signals. Long wire leads allow wiring through the baseboard without any joints to worry about.
SMD LEDs are Available in Packets of 2 Each in Following Clear Colors:
Resistors & Diodes
included with SMDs.
See Support
for details.
Stock Status White
SMD3528-WH:
Price: $2.50 per pkt.
Stock Status Warm White
SMD3528-WW:
Price: $2.50 per pkt.
Stock Status Yellow
SMD3528-YE:
Price: $2.50 per pkt.

S5 - 5v Lighting Strip
S5: Our 5v Lighting Strip
(Designed and produced by TrainAidsA)

Provides full strength illumination at 5-6v. Lower intensity at 3-4.9v. For 6v to 19v, we suggest using S12 strips.
 
Dimensions and other characteristics, same as S12 (see next item below).
 
Connector wire 10cm/4 in. long. Works with AC, but can also be used with a rectifier, built into the ACW connector wire. See item ACW below.
 
Our LED Support section provides additional information including their connectivity options for all strips, SMD Type LEDs etc.
(Details: Click image) 		5v version of our S12 SMD Lighting Strip ( next item below) for passenger cars & caboose/guard van, buildings, station platforms etc. "Plug-n-Play" for use with 3-6v DC. We recommend our mini rectfiers for AC or dual polarity use.

S5 SMD LED Strips are Available Singly in Following LED Colors:
S5WH: White
Price: $3.50 Each Stock Status
S5WW: Warm White
Price: $3.50 Each Stock Status
S5YE: Yellow
Price: $3.50 Each Stock Status

S12 - 12v Lighting Strip
S12: Our 12v LED Lighting Strip
(Designed and produced by TrainAidsA)

Lower than 12v will deliver slightly lower intensity of illumination. Reduce current for voltages higher than 18v for use upto 27v. by adding our 5R180 Resistor. See these in our Elektrizmos Section.
 
Picture shows two strips with two connector wires included. Sold singly with wire leads and connectors.
 
Length:
    10cm / 4 in ( 10.75 incl. connectors).
Width:
    8mm (0.32 in). Designed Power:
    12v (See our Notes).
Max. Forward Current:
    60mA (Reduce for voltages higher than 12v)
Max. Normal Current:
    40mA
Max. Reverse Voltage:
    10v
 
Our LED Support section provides additional information including their connectivity options, SMD Type etc.
(Details: Click image) 		SMD Lighting Strip for passenger cars. "Plug-n-Play" for use with 6v-19v DC and will work without any additional circuitry.

Used as is, in Marklin AC, and by our customers with DC/DCC as well. However, many prefer to use with ACW (see below). Our wire connector that has a built in mini-rectifier. That converts the power to DC. Connect two strips for longer passenger cars. Connect more for other uses such as background lighting, long stretches as platform lighting or illumination undel the layout table.
Strips can also be cut in half for adjustment to total length required or for shorter lengths for example for a Caboose/Guard Van. Half the strip (5cm/2 in.) will work just as normally as a complete one. Visit our Gallery section for ideas.

Please also see the longer version - S50 - below.
S12 SMD LED Strips are Available Singly in Following LED Colors:
S12WH: White
Price: $3.50 Each Stock Status
S12WW: Warm White
Price: $3.50 Each Stock Status
S12YE: Yellow
Price: $3.50 Each Stock Status

S12K - 12v Lighting Strip Kit
S12K: Our Lighting Strip Kit
(Designed and produced by TrainAidsA)


Each item/kit ordered contains:
2 Pcs: S12 (10cm) 12v SMD LED Strips
2 Pcs: R1 Mini Rectfiers for AC
2 Pcs: 1N4148 Diodes
2 Pcs: Wire with Connectors

Use "bridge rectifiers" (included) to correct polarity of power, or for handling both directions in DC. Strips work with voltages from 9v to 18v. Lower than 12v will deliver lower intensity of illumination upto a pont. Preferable to reduce current at higher voltages than 12v.
 
Our Support section provides additional information, including their connectivity options and other tips, including SMD Type etc.

 
 
 
 
 
 
 
 
 
(Details: Click image)

S12 Lighting Strip Kit for passenger cars. As a Kit, it offers additional flexibility in installation.

Strips can also be cut in half for shorter lengths for example for a Caboose. Half the strip (5cm/2 in.) will work just as normally as the complete one. Visit our Gallery section on LEDs for ideas.

Our LED Support section provides additional information.


S12 SMD LED Strip Kits are Available in Following LED Colors:
S12KWH: White
Price: $11.00 Each Stock Status
S12KWW: Warm White
Price: $11.00 Each Stock Status
S12KYE: Yellow
Price: $11.00 Each Stock Status


Interesting Links: Power Pickups, Axle & Wheel Wipers
Installing Our Pickups
Related Components & Devices

S50 - SMD LED 50cm. Long Lighting Strip
Same as S12, but Long Length SMD Lighting Strip.

Has different connectors. Cuttable & Plug-n-Play designed for use with 12v DC and will work without any additional circuitry. Works with voltages from 9v to 18v. Lower than 12v will deliver lower intensity of illumination upto a certain point. It is preferable to reduce current for voltages higher than 12v. Use these to light station platforms, inside buildings etc. Cut pieces will operate as independent Plug-n-Play strips.
 
Length: 50cm / 19 in
Width: 8mm (0.32 in)
Power: 12v
Max. Forward Current: 60mA
Max. Normal Current: 40mA
Max. Reverse Voltage: 10v.
Uses SMD Type 3528.

Shipping Note: Shipping of this item may not be combined with other items, due to its size and shape, but shipping calculation includes shipping for this item.

 S50 SMD LED Strips are Available Singly in Following LED Colors:
Stock Status S50WH: White / $15.00 Each
Stock Status S50WW: Warm White / $15.00 Each
Stock Status S50YE: Yellow / $15.00 Each
Stock Status S50BL: Blue / $15.00 Each
Stock Status S50RD: Red / $15.00 Each


Fx - 12v Flexible Lighting Strip
Fx: Our Flexible LED Strip
(Made available by TrainAidsA)

Power: As in S-50
 
Installation: Comes with Adhesive Backing
 
Maximum Continuous Length Available in one piece: 5 Mtrs (Approx 5 yds.)
 
Width: 8mm (0.32 in)
 
Cuttable in 2 inch / 5cm lengths only.
 
SMD Type 3528.

Our Support section provides additional information.
(Details: Click image) 		Designed for 12vDC. Does work with voltages from 9v up to 18v. Power supply lower than 12v will deliver lower intensity of illumination.
(Cut to Length as needed. Similar to S-50).

Flexible SMD LED Strips are Available in Following LED Colors
(Each 2in/5cm length is counted as one item)

FXWH: White - Price: $2.00 per item Stock Status

FXWW: Warm White - $2.00 per item Stock Status
FXYE: Yellow - Price: $2.00 per item Stock Status
FXBL: Blue - Price: $2.00 per item Stock Status

ACW - Wire Connector with Rectifier - for Polarity Control
Note: ACW can be used with other LEDs for polarity control. Just cut off the connector.
Do remember to mark the output side for reference. This is because both,
the input and output look the same, once the connector is cut off.
ACW: Our Power feed with Rectifier (Designed and produced by TrainAidsA)

Colored wire is positive. Only one needed if two or more strips connected or powered from the same feed. Highly recommended for digital systems.
 
Our Support section provides additional information on where and how to use ACW.
 
For individual mini rectifiers, see our Elektrizmos section.
(Important: Click image) 		Wire Connectors for S12/S5 Lighting Strips, with in-line Rectifier. Use with S12/S5 Lighting Strips directly.
Can also be used for Polarity control in other LEDs. (Click Image)
We also recommend that you visit our LED Support Section.

ACW - Strip Wire Connector with Rectifier is Available Singly
ACW - Price: $1.00 Each Stock Status

ACCW - Feed wire for Flicker Free LEDs

ACCW: Our Power feed with Rectifier & Capacitor

(Designed and produced by TrainAidsA)
 
Uses a Bridge rectfier & a 25v/220uF Capacitor. Colored wire is positive. Only one needed if
two or more strips connected or powered from the same feed. Highly recommended for digital systems.
Rectfier:
Max Surge Current: 35 A | Power Dissipation: 1.4 W | Termination Style: SMD/SMT
Max Voltage Drop: 1 V | Forward Surge Current: 35 A | Forward Voltage: 1 V
Forward Continuous Current: 0.5 A | Reverse Voltage: 600 V
 
Our Support section provides additional information on where and how to use ACW / ACCW.
The ACCW has an additional advantage of reducing the flicker that accompanies LEDs
when used in AC or DC environment. For individual mini rectifiers, see our Elektrizmos section.
 
Note: ACCW can be used with other LEDs for polarity & flicker control.
Just cut off the connector. Do remember to mark the output end for reference.
This is because both, the input and output look the same, once the connector is cut off.
The connector is at the output end.
 Flicker Free Wire Connectors for S12/S5 Lighting Strips, with in-line Rectifier & Capacitor for "flicker free" lighting. Use with S12/S5 Lighting Strips directly.
Can also be used for Polarity/Flicker control in other LEDs. (Click Image)
We also recommend that you visit our LED Support Section.

ACCW - Flicker Free Connector Wire is Available Singly
ACCW - Price: $1.50 Each Stock Status

(Important: Click image)

End Connectors for 10cm LED Strips
End Connectors:
For 10cm LED Strips
(Made available by TrainAidsA)
(Details: Click image) 		Pair of End Connectors for S12/S5 Lighting Strips. Solder connectors to shorter pieces of S12, S5 or S50 and make them connectable. Use with Lighting Strips or where needed. Good as wire connectors too. Sold in pairs as shown.

Strip End Connectors are Available as Pairs
Connectors - Price: $0.75 per pair. Stock Status


Please Note!
 
On subscribing, an email will be sent to you.
Please respond to that email to "confirm" your subscription.
 
Your subscription would not be completed
. . . until your confirmation is received by the mailing system.
 
Thank you!
 



Back to Top
 


Best viewed in Mozilla/Firefox | Safari | Netscape | Opera | Download Firefox Now |
| Copyright © 2008-2011. TrainAidsA, Inc. |